Proizvodi

Model: MPC-102S
Test Standards: PP: ASTM D6749, ASTM D97, ISO 3016; CP: ASTM D7683, ASTM D2500, ISO 3015
Specimen Volume: 4.5ml
Measurement Modes: Selectable from various modes. 1.CP mode (0.1 or 1.0 °C intervals) 2.PP mode: Programmed by the user. Programmable parameters are: *Amount of applied air pressure for PP detection, to accommodate different sample types: L(low) for diesel fuels, H(high) for lube oils, VH(very high) and UH (ultra high) for residual fuels and similar samples. *Testing intervals: 1.0°C, 2.5°C, or 3.0°C (In total, 4x3=12 modes for PP.) 3.CP/PP modes: CP is determined and then PP. PP detection is programmable by the user with the same parameters as PP modes.
Measuring Range: -65°C to +51°C
Sample Automatic Pre-Heating: Automatic preheating at either +45°C or EPP+10°C. (EPP=Expected Pour Point)
Display: Big digital display on VFD for showing real time parameters (sample temperature, bath temperature, test results).
EPP Setting: EPP (Expected Pour Point) needs to be set prior to test starts.
Specimen Cup: Cylindrical glass test jar with 4.5ml sample volume with reflex seal on the bottom for cloud point test.
Sensors: Compound type sensor assembly for PP and CP. PP detected by air pressure method (patented). CP detected photo-electrically. PT100 temp. sensors.
Sample Cooling Rate: As standard, 4°C/min. till EPP+40°C, and 1°C/min. Thereafter cooling profile is programmable.
Safety Shutdown: As hot side of TED reaches 60°C while preheating, warning buzzer beeps and heating stops.
Data Output: RS-232C 1 channel (for PC or Optional Printer)
Power Supply: 100VAC to 240VAC 50/60Hz
Power Consumption: 80 Wh for 1 test (about 1 hour), 30g CO2 (@0,378 Kg CO2 / 1000 Wh)
Operating Ambiental Temperature: 10 to 35°C
Size (W x D x H): 300 x 460 x 320 (mm)
Weight: 11 Kg

Bath Model: CB-80C
Bath Temperature Range: -70°C to +80°C
Bath Temperature Control: PID control with 2 points of revision functions
Bath Size (W x D x H): 222 x 407 x 238 (mm)
Bath Weight: 13 Kg

IQ/OQ/PQ Qualification: Yes, possible

Model: MPC-102L
Type:: Mini Pour Point(PP) and Cloud Point(CP) tester with sequential CP and PP measuring capability. Sample cooling and pre-heating by TED.
Test Standards: ASTM D6749/D97, ISO 3016 (PP), ASTM D7683/D2500, ISO 3015 (CP)
Specimen Volume: 4.5ml
Cooling: Liquid Cooling
Measuring Range: -40°C to +51°C with tap water of 20°C; -65°C to +51°C with cooling liquid of -35°C (*:Sample viscosity, etc. affects on lowest temperature of the measuring range.)
Measurement Modes: Selectable from various modes. 1.CP mode (0.1 or 1.0 °C, selectable) 2.PP modes: Programmed by the user. Programmable parameters are: *Amount of applied air pressure for PP detection, to accommodate different sample types: L(low) for diesel fuels, H(high) for lube oils, VH(very high) and UH (ultra high) for residual fuels and similar samples. *Testing intervals: 1.0°C, 2.5°C, or 3.0°C (In total, 4x3=12 modes for PP.) 3.CP/PP modes: CP is determined and then PP. PP detection is programmable by the user with the same parameters as PP modes'. (12 modes in total.)
Sample Automatic Pre-Heating: Automatic preheating at either +45°C or EPP+10°C. (EPP=Expected Pour Point)
Display: Test parameters, EPP, bath temperature, sample temperature, PP, and CP displayed on VFD. Temperatures displayed in 0.1°C increments.
EPP Setting: EPP (Expected Pour Point) needs to be set prior to test starts.
Specimen Cup: Cylindrical glass test jar with 4.5ml sample volume.
Sensors: Compound type sensor assembly for PP and CP. PP detected by air pressure method (patented). CP detected photo-electrically. Pt100 temperature sensors.
Sample Cooling Rate: As standard, 4°C/min. till EPP+40°C, and 1°C/min. Thereafter, cooling profile is programmable.
Safety Shutdown: As hot side of TED reaches 60°C while preheating, warning buzzer beeps and heating stops.
Data Output: RS-232C 1 channel (for PC or Optional Printer)
Data Strage: Last 50 test data are stored in RAM
Power Requirements: 100, 120, 220, or 240VAC 0.5kW
Dimensions (WxDxH) (mm) and Weight: 230mm x 480 x 385, 20kg

IQ/OQ/PQ Qualification: Yes, possible

Model: MPC-102A
Type:: Mini Pour Point(PP) and Cloud Point(CP) tester with sequential CP and PP measuring capability. Sample cooling and pre-heating by TED.
Test Standards: ASTM D6749/D97, ISO 3016 (PP), ASTM D7683/D2500, ISO 3015 (CP)
Specimen Volume: 4.5ml
Cooling: Air cooling
Measuring Range: -30°C to +51°C (in 25°C ambient) (*:Sample viscosity, etc. affects on lowest temperature of the measuring range.)
Measurement Modes: Selectable from various modes. 1.CP mode (0.1 or 1.0 °C, selectable) 2.PP modes: Programmed by the user. Programmable parameters are: *Amount of applied air pressure for PP detection, to accommodate different sample types: L(low) for diesel fuels, H(high) for lube oils, VH(very high) and UH (ultra high) for residual fuels and similar samples. *Testing intervals: 1.0°C, 2.5°C, or 3.0°C (In total, 4x3=12 modes for PP.) 3.CP/PP modes: CP is determined and then PP. PP detection is programmable by the user with the same parameters as PP modes'. (12 modes in total.)
Sample Automatic Pre-Heating: Automatic preheating at either +45°C or EPP+10°C. (EPP=Expected Pour Point)
Display: Test parameters, EPP, bath temperature, sample temperature, PP, and CP displayed on VFD. Temperatures displayed in 0.1°C increments.
EPP Setting: EPP (Expected Pour Point) needs to be set prior to test starts.
Specimen Cup: Cylindrical glass test jar with 4.5ml sample volume.
Sensors: Compound type sensor assembly for PP and CP. PP detected by air pressure method (patented). CP detected photo-electrically. Pt100 temperature sensors.
Sample Cooling Rate: As standard, 4°C/min. till EPP+40°C, and 1°C/min. Thereafter, cooling profile is programmable.
Safety Shutdown: As hot side of TED reaches 60°C while preheating, warning buzzer beeps and heating stops.
Data Output: RS-232C 1 channel (for PC or Optional Printer)
Data Strage: Last 50 test data are stored in RAM
Power Requirements: 100, 120, 220, or 240VAC 0.5kW
Dimensions (WxDxH) (mm) and Weight: 230mm x 480 x 385, 20kg

IQ/OQ/PQ Qualification: Yes, possible

Model: AAP-6
Test Methods: ASTM D36, ASTM E28, EN 1427, IP 58, etc
Type: Two-rings & two-balls
Measuring Range: Ambient to 200?C (392?F )
Temperature Sensor: PT-100 in stainless steel sheath
Softening Point Detector: Light projector: LED; Light receiver: photo-diode
Display: 5.7" color LCD with back light
Heater: Nichrome coil heater: 1,000W @100V or 1,000W @220V
Sequense Control: By an on-board microcomputer
Test Mode: ASTM D36 water, ASTM D36 glycerin, EN 1427 water, EN 1427 glycerin
Stirring: Magnetic stirring, selectable from 0 to 250 rpm
I/O Port: 1x Ethernet for LIMS; 1x USB for Flash Memory or Keyboard; 1x RS-232C for LIMS / PC or Optional Printer
Data Memory: Last 200 sets of test results
Safety Mechanism: a) The sample falls on only one side and not on the other within the set temperature range, b) The sample does not fall on either side within the set upper limit temperature, c) Light projector or receiver is found defective, d) Temperature sensor is found defective, e) Temperature sensor is not placed in the right position, f) Built-in battery is found drained out, or g)Control computer runs away (no display)
Size (WxDxH): 230 x 470 x 440 (mm)
Weight: 15 kg
Ambiental Conditions: RT: 10 to 40?C, RH: Less than 90% (no condensation)
Power Supply: AC100/120 V or 220/240V 50/60Hz (set at the factory, specify when ordering) 1,500W ( max.)

IQ/OQ/PQ Qualification: Yes, possible

Model: AAP-6
Conforming Standards: ISO2977, ASTM D611, etc.
Measuring Range: Ambient +20°C to 170°C, for bellow ambient temperature + 20°C, the optional water jacketed measuring cell and a cryostat must be used.
Temeprature Sensor: Pt100 in stainless steel sheath
Aniline Point Detector: Photo-electric cell with special detection circuitry
Measuring Cell: Modified U-Tube type, vacuum jacketed glass cell with PTFE stopcock at the bottom for drainage.
Display: 5,7" color LCD with LED backlight
Heater: Immersion heater in stainless steel sheath: 20W
Sequense Control: By an on-board microcomputer
Test Mode: Sinle, repeat (2 kinds, average is reported to nearest 0,05°C), SPE and manual temp set
I/O Port: 1x Ethernet for LIMS, 1x USB for Flash memory or keyboard, 1x RS-232C for PC or optional printer
Safety Mechanism: Automatically shuts off and the problem is reported by buzzer and display in case: a) EAP+10°C or 170°C is reached, b) Temperature sensor is found defective, c) Light projector or receiver is found defective, d) Built in battery is found drained out, e) Control computer runs away (no display)
Dimensions (W X D X H): 230 x 470 x 490 mm
Weight: 14Kg
Ambiental Conditions: 10 to 40°C, Relative Humidity less than 90%
Power Supply: AC 100 to 240V; 50/60Hz; 125W max

IQ/OQ/PQ Qualification: Yes, possible

Model: AKV-202
Type: Bench top automatic KV measuring system with 2 viscometers in 1 bath
Related Standards: ISO 3104, ASTM D445, IP71, etc.
Viscometers: Modified Lanz-Zeitfuchs viscometers
Measuring Range: 10,000 mm2 /s for automatic operation. (Range depends on viscometer.)
Meniscus Detection: By photo-electric devices with fiber optics
Timing: 0.00 - 999.99 sec
Bath: Stainless Steel bath with drain, 18 liters
Bath Heater: Sheathed heaters, 0.59kW x2
Bath Lighting: Fluorescent light, 6W
Bath Medium: Water (distilled or ion exchanged) for < 75°C, Colorless/transparent silicon oil (with PMCC flash point of 190°C at minimum and KV of 10-20mm2/s) for >= 75°C.
Bath Temperature Controller: Temp: Preset at 6 points. Preset point can be set at any temp between 20 and 100°C; Precision: ±0.01°C
Cleaning/Drying Viscometers: An automatic cycle consisting of draining sample, injecting chemicals, and drying with air. By vacuum; Chemicals: BTX for cleaning, Ethanol ?Bath Temp <80°C?for drying. (Ether or Ketone can not be used); Fume: Fume to be exhausted through trap and hose to outside
Display: Test parameters, status, trouble, etc. displayed on fluorescence display module
Printer: Thermal printer, 58mm of paper width
Computer Output: RS-232C, 1 channel
Safety: Alarms for gas, bath medium level, & bath overheat
Power Requirements: 100, 120, 220 or 240VAC, 2 KW
Dimension & Weight (Wxdxh): 530mm x 560mm x 930mm, 75kg

IQ/OQ/PQ Qualification: Yes, possible

Model: AVP-30D4
Related Standards: ISO 3007, ASTM D323, IP69 etc.
Type: Bench-top automated instrument. Automated continuous shaking of test cylinder by "seesaw" motion.
Number Of Cylinders (Measurement Spots): 4
Measuring Range: 0 to 196 kPa (2 kgf/cm2)
Test Cylinders: Small size stainless steel cylinders with 66% in length and 31% in volume compared to the regular full size cylinders. The V/L ratio of 4 is the same as full size cylinder. A "Quick Coupler" is equipped at the center of the vapor cylinder for connecting to external pressure sensor located inside of the tester
Pressure Sensor: Semiconductor type pressure sensor.
Range: 0 to 196 kPa (2kgf/cm2)
Linearity: <0.3% of the range
Hysteresis: <0.3% of the range
Display: LCD with back light
Pressure Display Range: 0 to 200 kPa or 0 to 2 kgf/cm2
Shaking: By "see-saw" movement with angular movement of +/-15 degrees and interval of 6 sec
Bath Temperature Range: Ambient to 60°C
Temp Control: Digital controller/display with PT-100 Sensor, Precision: +/-0.1°C
Stirring: By propeller driven by motor
Heater: Stainless sheathed heater 1.15kW
Calibration: By connecting a Digital Manometer (optional) to the pressure sensor
Safety Mechanism: Water level monitoring device for preventing overheating due to low water level
Data Output: 1xRS-232C channel (for PC or Optional Printer)
Dimension & Weight: 400W x 600D x 720H (mm), 50kg when dry, 85kg when filled with water
Installation Site: Ambient temperature: 0 to 40°C
Relative Humidity: Less than 90% (no condensation)
Power Supply: AC100/120V or 220/240V 50/60Hz (set at the factory) 1.5 kW (max.)

IQ/OQ/PQ Qualification: Yes, possible

Model: TCU-40B
Temperature Range: -40°C to Ambient
Temperature Control: By digital display controller, ON/OFF control
Temperature Stability: +/- 1°C
Cooling Capacity: 87W@ -40°C, 158W@ -30°C, 212W@ -20°C (@50Hz)
Pumping Capacity: Max Head: 2.0m, Max Flow Rate: 10lit/min, Force type
Bath Volume: 7 litre
EPP Setting: Current Leakage Breaker
Power Source Voltage: AC 120V, 220V-240V *Specify when ordering
Power Consumption: 700W max.
External Dimensions: 320(W) x 590(D) x 725(H) mm
Weight: 55kg (AC120V); 60kg (AC220-240V)

Model: AFP-102
Conforming Standards: IP309, ASTM D6371, EN116 and JIS K2288
Type: 1 test head.
Specimen Volume: 45ml
Measuring Range (Typical): RT to -60°C (The lowest temperature varies with the chiller liquid temperature and ambient temperature.)
Sequence Control: By a built-in micro processor
Display: By a fluorescence display (VFD) Temperatures displayed with 0.1°C increments
Temperature Sensor: Pt-100
Cfpp Detection: By means of a photo-electric detector consisting of an LED, photo transistor, and light guide (fiber optics). Upper and lower light guides are mounted on sliding type holder.
Vacuum Regulator: Consists of a micro air pump, pressure switch, solenoid valve and a plastic bottle.
Cooling And Heating (Needs Optional Chiller): By Peltier cells. The hot side of the Peltier cells needs to be cooled by external chiller.
Temperature Control: By step (-34°C, -51°C and -67°C) or linear. The linear cooling rate can be programmed.
Safety Features: a) Over cut: as hot side of TED reaches 60°C, warning buzzer beeps and stops. b) Self diagnostic: reported by an intermittent buzzer and a text message when any temperature sensor breaks down or the battery has drained out. c) System trouble: reported by a buzzer when the built-in microprocessor runs off.
Data Output: 1x RS-232C (for PC or Optional Printer). 2nd set channel is optional.
Power Requirements: 100 or 120VAC, 5A; 220 or 240VAC, 3A Please specify AC voltage when ordering.
Dimensions And Weight: 350W x 550D x 480H mm, 27kg

IQ/OQ/PQ Qualification: Yes, possible

Model: PX224
Kataloški broj: 30429804
Odobren model (kod Direkcije za mere i dragocene metale): Da
Kalibracija: Interna
Kapacitet (g): 220
Rezolucija (g): 0,0001
Ponovljivost (STDEV) (g): 0,0001
Linearnost (g): ±0,0002
Vreme stabilizacije (s): 4
Osetljivost temperaturnog odstupanja (PPM/K): ± 3
Tipična minimalna masa merenja prema USP (USP K=2, U=0,10%): 200 mg
Optimizovana minimalna masa merenja (USP, U=0,10%, K=2) SRP≤0,41d*: 82 mg
Jedinice merenja: Milligram, Gram, Kilogram, Ounce, Pound, Carat, Pennyweight, Ounce Troy, Grain, Newton, Hong Kong Tael, Singapore Tael, Taiwan Tael, Momme, Tical (MM), Mesghal, Tola (India), 1 Custom unit
Aplikacije: Osnovno merenje mase, Brojanje komada, Procentulano merenje, Merenje životinja, Određivanje gustine
Dimenzije merene ploče (Ø): 90 mm
Napajanje: Ulaz: 100-240V; 200mA 50-60Hz 12-18VA, Izlaz: 12VDC 0,5A
Dimenzije vage (Š x D x V): 209 x 321 x 309 mm
Komunikacioni interfejsi: RS232 i USB
Opseg radne temperature: 10°C do 30°C
Neto težina: 4,5 kg
Težina transportnog pakovanja: 7 kg
Dimenzije transportnog pakovanja (Š x D x V): 507 x 387 x 531 mm

IQ/OQ/PQ Kvalifikacija: Da, moguća je

*: Vrednost SRP je standardna devijacija za n broj merenja (n≥10)